VSR-10 Upgrade Guide
VSR-10 Upgrade Guide
Tags: a, Guide, Upgrade, Upgrade Guide, Vsr 10, vsr 10 upgrade without remove the pin, Vsr10
| AirSoft Sniper Rifle |
| AirSoft Sniper Rifles and Gear |
VSR-10 Upgrade Guide
Tags: a, Guide, Upgrade, Upgrade Guide, Vsr 10, vsr 10 upgrade without remove the pin, Vsr10
May 20th, 2010 at 9:27 pm
hay thanks for the vid ive had so much trnble trying to up grade my vsr 11 as its now 6 or 7 years old and now cums out at 200 fps so now its upgrade time haha and i would recomend thit rilfe to any sniper ive been able to get about 10 ft from target and thay dont hear the shoot
May 20th, 2010 at 9:30 pm
very usefull thx
May 20th, 2010 at 9:40 pm
Thank you for a very informative and useful video.
Very helpfull for me as I prepare to dismantle & upgrade for the first time. (VSR)
May 20th, 2010 at 10:37 pm
hay can you do the same thing with a AGM because i cant get the little switch to take out the bolt
May 20th, 2010 at 11:34 pm
Do u know where I can buy a better spring to improve the fps on my agm mp001?
May 21st, 2010 at 12:15 am
nice vid man gonna help me when i get my gun XD
May 21st, 2010 at 12:35 am
@BlitzedBitc you can’t just do that with the vsr 10 model
May 21st, 2010 at 1:35 am
Or just unscrew the cylinder head..
May 21st, 2010 at 2:29 am
the only reason i watched this was to find out how to take the gun apart so thanks
May 21st, 2010 at 3:22 am
Umm.. i dont know much about HFC things but if your budject is under 100 euros i think u can´t get reliable gun, sorry man.
May 21st, 2010 at 3:48 am
@TheGuitarguy321 i agree but u could buy another bolt but i can only find the laylax ones which are £99 abouts
May 21st, 2010 at 4:22 am
does it work with the agm mp001
May 21st, 2010 at 4:45 am
mm, if som1 would help over here.
just a offtop topic kinda, but what all i need to install M150 Spring to my HFC vsr-11, so it work properly? the spring oviosly, maybe sylinderhead, and some other shit? please advice the stupid.
(budject is mostly under 100€)
May 21st, 2010 at 5:04 am
Alguien me puede decir para que ha usado el taladro?..por favor
May 21st, 2010 at 5:45 am
dude my hats off to you, thanks for the vid. searching for abit looking for a good how to.. mad props. ty
May 21st, 2010 at 5:58 am
The jg bar 10 is sooooo much easier to disasemble. But it isnt a marui…… :,(
May 21st, 2010 at 6:55 am
i realy dont wanna drill a hole in my piston or bolt! is there any other way??
May 21st, 2010 at 7:48 am
Or you can find a better spring and put it in
May 21st, 2010 at 8:30 am
@Airsmoke99 The same springs should work with most guns, the main reasons guns can’t handle springs is because of the gearbox. Any spring under 600 fps should work in a well. You may need a new piston and spring guide, too, depending on the fps of the gun. Systema pistons and spring guides are recommended.
May 21st, 2010 at 8:39 am
it unscrews on my VSR-10
May 21st, 2010 at 9:09 am
does the same springs work with well mb03 (upgrade)
May 21st, 2010 at 9:48 am
the hole is just to remove a pin thats put in there t hold the piston head on. you dont need it
May 21st, 2010 at 10:19 am
@Vili738 Thought so or the air would rush out (:
Ive done a tightbore upgrade in mine with a 6.01 and i can tell it was worth it, the range goes up so much
such a great gun i recomend a tightbore and a 120 spring its fine with just that O_O
Can you recomend a decent lube for the internals?
Cheers
May 21st, 2010 at 10:36 am
nice guide
May 21st, 2010 at 10:39 am
@Greataardvark I refilled it!